Loading contract…
BETAThis is a new independent transparency project, not an official government website. The data is sourced from public registers and may contain errors, so always verify against the official source. If you find a problem, please report it here.
Chippenham Town Council invites companies to supply competitive quotes for the supply of the following:
A COMPACT SWEEPER SWINGO 200+ PUSHED 2-BRUSH SYSTEM
Specification
Engine
Euro6 - Common Rail
4 cylinder, displacement 2960 to 3000 cm³
60 kW to 65 kW @ 2300 to 2500 rpm
Max. torque 270 Nm @ 1350 rpm
Transmission
Full hydrostatic transmission with 2 drive modes (sweeping + transit) via rear axle with differential
Stepless and automatic load-dependent transmission control (automotive drive)
Axles
Hydraulic power steering
Selectable 4-wheel steering
Tyres 225/70 R15 to 225/80 R15
Mechanical/Coil spring suspension for front and rear axle inc damper and front anti-roll bar
Cab
Cabin with two seats mounted on elastic rubber elements for low vibrations
Ergonomic high back driver's seat with mechanical or air stepless suspension adjustment, fully adjustable
Driver and passenger side sliding windows
Heater / ventilation with recirculating and fresh air with adjustable vents. Minimum of 10 vents, 6 adjustable
Air conditioning
Height and inclination adjustable steering column
One key operating fuel cap, doors and ignition. Minimum of 3 keys supplied per vehicle
Central Colour display with information on all relevant vehicle data and board computer, incl. on board diagnostics
Control of the sweeping systems via an ergonomic door control panel with joysticks
Cruise control function
Cab floor windows for optimum view on brushes and suction nozzle
Water System
Fresh water tank: 175l to 190l
Re-circulating water tank: 175l to 190l plus Re-circulating water up to 250l in hopper
Total Re-circulation water 350l to 440l
Total water capacity 500l to 630l
Re-circulating water discharge via in cab control
Water tank made of impact resistance polymer
2 water nozzles per brush- adjustable directly on the brushes
Brush System
Heavy duty pushed 2-brush-system
Brush diameter 800mm to 900mm
Hydraulic ground pressure adjustment
Brush speed individually adjustable 0 - 130 max rpm
Brush material either Plastic (Poly), mixed (steel-Poly) or steel
Suction
Hot galvanized steel suction box for enhanced corrosion protection and strength
Guided on swivelling castor wheels
Hydraulic activated debris flap
Hydraulic lifting including incremental lifting to nozzle box
Pulled nozzle box system to ensure increased damage protection
LED work light to illuminate the work area around the suction nozzle box
Hopper
Drilled Hopper Screen not wired
Aluminium corrosion resistant construction
1.9 to 2.1m³ gross volume
Suction tube in the hopper made of stainless steel
Dirt water separation screens made of stainless steel, mounted to front and side walls in the hopper
Hopper lid hydraulic operated, can be opened separately
Hopper functions can be controlled in cab or via external control pendant
Hydraulic tipping to the rear - 1.400mm to 1.550mm
Manually operated hopper raise feature in case of engine breakdown/ loss of power
Hydraulic system
Load-Sensing hydraulic system
Hydraulic tank made of impact resistance polymer
Hydraulic filter blockage and hydraulic oil low level and hydraulic temp. warning system
Hydraulic steel pipes with factory fitted protected against corrosion
Brake System
Hydraulic servo assisted brake system on all 4 wheels
Dual circuit brake system (acting on front and rear axle)
Disc brakes on front and rear axle
Electro hydraulically operated parking brake with hill hold assist
Electric System
12 Volt battery with 90 to 100 Ah
Alternator 12V greater than 130A
Lighting according to EC regulations
Beacon foldable with protection bracket
Dimensions
Height with beacon 2.350mm max
Height without beacon 1.900 mm to 1.990 mm
Wheelbase up 1.810mm to 1.910mm
Length with brushes up to 4.600 mm
Width without brushes up to 1.315 mm
Steering / turning Circle
4-wheel steering switchable in cab
Turning cycle Kerb to Kerb up to 4.750 mm
Weights
Payload between 1.750kg and 2,100kg
Gross vehicle weight up to 5,000kg
Other items
Hopper painted in white with chapter 8 markings
DAB + Radio with USB connection and Bluetooth hands-free module
Reversing signal disengage able
Rear view and suction nozzle camera
Between 140 bar to 150 bar high pressure washer in frame with 8m to 10m hose recoil drum and
900m Hand Lance.
Additional Requirements
Rear mounted wonder hose
Near side weed control system incorporating reinforced brush arm, rated lift arm, heavy duty brush,
Motor and weed ripping brush, independent brush lift control and brush head articulation controlled
From cab
Training
Train the operator training for 2 operatives
The Council would be interested in receiving quotations to outright purchase the above vehicle.
For further details interested parties should contact either:
Wayne Lewkowicz
Environmental Services Supervisor (Streetscene)
07875 665502
…@chippenham.gov.uk
Or
Will Tidmarsh
Head of Environmental Services
07875664690
Email: …@chippenham.gov.uk
Chippenham Town Council
Town Hall
High Street
Chippenham
Wiltshire
SN15 3ER
Tel: 01249: 446699
Email: …@chippenham.gov.uk
Terms and Conditions:
i) All prices tendered are to be net of VAT which are to be added by the successful tenderer at invoice stage.
ii) A Chippenham Town Council Purchase Order will be issued to the successful tenderer as confirmation of the works.
iii) The successful Tender will be paid in full in the 2026/27 financial year.
iv) Reservation: The Town Council reserves the right to not accept the lowest, or any Tender.
Tenders must be provided on the attached form and returned either:
In an envelope addressed to - Chippenham Town Council CEO, Town Hall, High Street, Chippenham, Wiltshire, SN153ER, and Marked COMPACT SWEEPER SWINGO 200+ PUSHED 2-BRUSH SYSTEM or via email to …@chippenham.gov.uk.
Failure to do this will lead to disqualification from the quotation process.
TENDER FORMS MUST BE RETURNED BY: 09 March 2026.
No supplier information available.
This procurement was divided into 1 lots, each awarded separately.
| Lot | Value | Status |
|---|---|---|
| Lot 1 Apr 2026 – Apr 2031 | - | active |