BETAThis is a new independent transparency project, not an official government website. The data is sourced from public registers and may contain errors, so always verify against the official source. If you find a problem, please report it here.
Loading contract…
Plowright and Brooksby CETP BETP Calibrations Service Contract — THE PIRBRIGHT INSTITUTE | UKGovscan
Loading contract…
AWARDEDProcurement termination notice (UK12) · THE PIRBRIGHT INSTITUTERef ocds-h6vhtk-05e2ad
Plowright and Brooksby CETP BETP Calibrations Service Contract
The Pirbright Institute (Pirbright) is a world-leading centre of excellence in research and surveillance of virus diseases of farm animals and viruses that spread from animals to humans, working to enhance capability to contain, control and eliminate these economically and clinically important viral diseases (such as foot-and-mouth diseases virus (FMDV)) through highly innovative fundamental and applied bioscience. The facility also plays a crucial role in predicting which viruses are circulating globally and assessing their potential impact. This capability is essential for preparing and responding to outbreaks, ensuring rapid diagnostics can be deployed in the UK.
The Pirbright Institute is inviting tenders for Plowright and Brooksby CETP/BETP Calibrations Service Contract at The Pirbright Institute.
Contract Scope
The Pirbright Institute is seeking a qualified contractor to provide comprehensive calibration services for all critical instruments associated with three Effluent Treatment Plants (ETP) systems across its research facilities.
This includes:
Scheduled calibration of all sensors and instruments, split between critical (6-monthly) and non-critical (12-monthly) frequencies.
Provision of calibrated, UKAS-traceable test equipment by the contractor.
Provision of calibration certificates, registers, and documentation for all instruments.
Compliance with biosecurity, quarantine, and barrier shower entry/exit procedures while working under escort in high-containment environments.
Attendance at site for planned visits totalling approximately 27 days per year (18 days for Plowright CETP and BETP, 9 days for Brooksby BETP).
Any additional days required to complete calibration will be billed separately under the contractor’s standard fee rates.
Replacement of faulty or non-calibratable equipment will be costed and sourced separately under independent Purchase Orders.
Equipment Covered
The following systems are included in this contract:
Plowright Building
Continuous Effluent Treatment Plant (CETP)
Batch Effluent Treatment Plant (BETP)
Approx. 239 instruments across both systems.
Brooksby Building
Batch Effluent Treatment Plant (BETP)
Approx. 131 instruments.
Total: 370 instruments across all systems.
Service Frequency
Every 6 months:
Calibration of all critical instruments essential for containment and process control (e.g., temperature probes, pressure transmitters, flow meters critical to biosecurity performance).
Every 12 months:
Calibration of all non-critical instruments (e.g., ancillary monitoring devices, level sensors, general process indicators).
This results in two calibration visits per year per building:
Visit 1: Calibration of all instruments.
Visit 2 (six months later): Calibration of critical instruments only.
Points to note:
A reasonable number of spare parts are to be held ready for call outs.
This procurement was divided into 1 lots, each awarded separately.
Lots
1
Lot
Value
Status
Lot 1
Jan 2026 – Jan 2029
-
cancelled
Key Dates
Published
17 November 2025
Tender Open
-
Tender Deadline
12 December 2025
Award Date
-
Contract Start
-
Contract End
-
Planned term
26 January 2026 – 25 January 2029
Procurement Details
Method
Open — any supplier may bid
Method Details
Below threshold - open competition
Route to market
Open competition
Main category
Services
Category
Instrumentation and control equipment
Buyer Reference
EMS/PBETP25-001
Legal Basis
Procurement Act 2023
CPV Codes
31682210 – Instrumentation and control equipment; 45232430 – Water-treatment work; 50000000 – Repair and maintenance services; 50430000 – Repair and maintenance services of precision equipment; 50433000 – Calibration services; 71700000 – Monitoring and control services; 90711500 – Environmental monitoring other than for construction