Loading contract…
BETAThis is a new independent transparency project, not an official government website. The data is sourced from public registers and may contain errors, so always verify against the official source. If you find a problem, please report it here.
3785/COMPASS/PRESS/JS/23-Press for COMPASS (Composites at Speed and Scale) Facility
The University of Sheffield wishes to invite tenders for a 'Press' on behalf of the Advanced Manufacturing Research Centre, Castings Group at Catcliffe, South Yorkshire.
Scope of Requirement
The AMRC has recently won funding for an 'automated, large scale composites manufacturing centre', including a 'fully automated layup and consolidation cell' which will incorporate a 10.5m (length) x 3.5m (width) x 2.3m (daylight) Press.
Within the 'Fully Automated Layup and consolidation cell' the Press will sit alongside a variety of other equipment, and will be in close proximity to the following:- o High Volume Deposition Cell - including Robot arms and guide rails;
o Press Heater System;
o Press Injection System;
o Oven Feed table.
The Press is to be used for manufacturing research into the production of large polymer composite components using several potential processes, including (but not limited to):- o Dry fibre pre-forming;
o Resin Transfer Moulding (RTM);
o Gap RTM/ Infusion;
o Wet Compression Moulding and Compression Moulding of pre-preg.
Brief Summary of Requirements
Please see G1, G2, G3, G4 and G5 for our exact technical and functional requirements, however at a high level these can be summarised as:- o The Press will have cold platens and that any heating for processing will be applied to the tooling rather than through the platens. A system of automated tool clamping, and location will need to be included within the tendered press platen package.
o The Press is expected to have a stroke of a minimum of 1500mm within the minimum daylight of 2.3m.
o The Press is required to have a moving lower platen that will enter and exit along the long axis from one end only. All controls and connections for the lower tool will remain active when the lower platen is fully extracted from the press.
o The AMRC is looking for flexibility in the size of tooling that can be used within the Press. The maximum size of component is defined for the purpose of this specification as 10m (length) x 3m (width) x 1.5m (depth) and this will require a minimum programmable force of up to 8 bar across the entire area of that part. Cost options for an incremental increase of this force up to 20 bar are requested (if possible).
o It is anticipated that the platens' size will exceed the maximum component size by approx. 0.5m in the X and Y axes (10.5m x 3.5m) to accommodate a part of 10m x 3m. To this end the tenderer is expected to recommend a suitable platen size within its proposal.
o The Press must be able to control the platens in a way that allows for tools shorter than the full length to be safely used. The limits to this function must be stated within your tender response.
o The Press will be expected to maintain the platens in an accurate Z plane whilst holding a full-sized tool open against a to...
Additional information: All expressions of interest must be via the University of Sheffield e-tendering portal:
https://www.in-tendhost.co.uk/Sheffield
This is an open tender exercise. The ITT can be downloaded by registering and expressing your interest on the University`s e-tendering system https://www.in-tendhost.co.uk/Sheffield
If you have any questions or comments in relation to this tender they must be submitted via the In-tend System, this can be accessed at https://www.in-tendhost.co.uk/Sheffield
Completed tenders must be returned through the same e-tendering system.
Closing date for receipt of tenders: 22 September 2023 at 12 noon (UK time).
Please note:
The University of Sheffield is not a contracting authority for the purposes of the Public Contracts Regulations 2015 (Directive 2014/24/EU) as amended by the Public Procurement (Amendment) (EU Exit) Regulations 2020.
The University reserves the right from time to time to voluntarily operate under the Public Contract Regulations (as defined above) on a case by case basis. Otherwise, advertisement of any contract in Find a Tender Service or Contracts Finder is at the sole discretion of the University and is undertaken on a voluntary basis with no implied obligation to comply with the procurement legislation.
For the avoidance of doubt, this procurement is not subject to the Public Contract Regulations (as defined above).
Delivery Notes delivery (plus installation/commissioning/acceptance) to AMRC Factory 2050, Europa Avenue, Tinsley, Sheffield, Rotherham S9 1ZA
Is a Recurrent Procurement Type? : No
No supplier information available.